Washington Department of Ecology

State of Washington Department of Ecology

The Washington Department of Ecology does not regulate the use or operation of residential heating oil tanks, like the State of Oregon does. However, some local governments may have different requirements or guidelines that may apply to residential storage tanks. Regulations and policies vary from place to place and may change from time to time.

Are there specific concerns I should have as a homeowner if I have an abandoned oil tank on my property?

  • Tanks can develop holes and release heating oil into the soil. The released oil can contaminate groundwater, surface water, storm sewers, and cause vapor problems in nearby buildings. Under the state Model Toxics Control Act, the tank owner may be held liable for damage caused by a leaking tank.
  • Corrosion can cause underground tanks to deteriorate, making cave-ins a possibility. The homeowner could be held liable for injuries caused by a cave-in.
  • Before finalizing the sale of a house, lending institutions and home buyers may want sellers to remove or “close” unused heating oil tanks. To “close” a heating oil tank, the homeowner has the tank cleaned out and filled. The tank is then left buried in the ground.
Washington Department of Ecology

Washington Department of Ecology – tank found within a backyard in Vancouver, vent pipe can be found running along the side of the house to the left of the window. The sampling of this tank resulted in a Risk Based Clean-Up.

How does Ecology prefer decommissioning take place?

Ecology recommends that the tank is removed with proper soil samples taken, and remediation, if necessary. However, decommissioning the tank in-place is also acceptable, as long as soil samples take place and remediation is completed, if necessary.

Can I decommission my tank as a homeowner?

There is no law prohibiting homeowners from doing their own decommissioning. Although, Ecology does not recommend doing the tank work yourself because of the potential safety risks. Hiring an experienced contractor is advised, as working on an underground storage tank can be dangerous. Under certain conditions, tanks can explode. Working in the excavation pit, cutting open or handling heavy tanks, and using power equipment also pose risks to the homeowner. Ecology recommends that homeowners hire an experienced contractor to perform decommissioning work.

Leaking tanks and the State of Washington Department of Ecology

What if a tank has leaked?

Knowingly using a leaking tank is negligence. If you discover that your tank is leaking you must take immediate action to stop the leak. In most cases where a tank has leaked, only the soil near the tank is affected. Sometimes, however, the heating oil may also have contaminated groundwater or surface water. It is the homeowners or contractors responsibility to:

  • Evaluate the extent of contamination caused by the leak
  • Evaluate the extent of the contamination caused by the leak
  • Determine if it is a threat to human health and the environment
  • Clean-up any contamination caused by the leak

Should I report the leak to Ecology?

Minor Leaks or Spills that affect only the soil near the residential heating oil tank do not have to reported to the Department of Ecology.   However, if the minor leak was discovered during the process of the tank being decommissioned, Ecology does recommend reporting the minor spill through the ERTS program.

Contaminated Soil above 2000 PPM does need to be reported to the Department of Ecology. Any groundwater, surface water, free product or vapor intrusion should also be noted during the reporting process.

How do I report a leak to Ecology?

All confirmed releases must be reported to the Washington Department of Ecology within 24 hours to the ERTS SYSTEM. A leak can be reported via a phone call or through the online reporting system.

Should I clean-up contamination?

Absolutely, and the Department of Ecology recommends that homeowners hire a qualified clean-up contractor to perform the remediation. When the clean-up has been completed, the contractor should give the homeowner a copy of the clean-up report. Clean-up reports of minor leaks do not need to be sent to Ecology, as they do not track or report on these clean-ups. Clean-up reports on more extensive leaks do need to be sent to the Ecology regional office, as they do keep track of and report on these sites. All reports should be kept by the homeowner for their records and the remaining life of the property.

Does the Department of Ecology have a LUST list like the State of Oregon?

Yes, it is called the Confirmed and Suspected Contaminated Site List (CSCSL). However, the majority of the sites on this list are large properties, with larger leaks (i.e. gas stations). It is extremely rare when a residential property does appear on this list, reasons that a site would appear on CSCSL is as follows:

  • When a property has been reported, but after 90 days, no closure and/or continued work to complete the remediation has taken place.
  • If groundwater has been encountered, the property automatically gets put on the CSCSL. The homeowner/contractor then has to go through the voluntary clean-up to get taken off the list. Ecology then works with the homeowner/contractor to get off the list by providing opinions on the work being completed and to verify if meets the status of no further action.

Additional Website Links:

Risk-Based Clean-Up

Risk-Based Clean-Up

Risk-Based remediation addresses the highest level of contamination from a leaking underground storage tank, with levels reported above 10,000 PPM. According to the DEQ, a risk-based clean-up offers the greatest amount of flexibility and adaptability to site-specific conditions. However, it is also the option that might require collecting additional site data and evaluation of more alternatives than a soil matrix or generic remedy clean-up. Risk-based clean-ups are the most rigorous option, with the collection of several soil samples to determine the magnitude and depth of contaminated soil, as well as how far the contamination has spread. The most important aspect of a risk-based clean-up is the evaluation of current and reasonably likely future risks to human health and the environment.

A risk-based remediation involves a soil investigation, which examines the pathways the contamination has likely spread. This pathway evaluation determines where the contaminants were released, how the contaminants can be transported to new locations and the reasonably likely ways that people may come into contact with them. Tests need to be conducted on enough samples to determine the lateral extent, as well as the depth of the petroleum contamination.

There are three investigative phases of concern while conducting a risk-based clean-up, phase two and three may not be necessary if the area of contaminated soil is limited enough in extent. Below are the steps, in order, that are required by the DEQ in order to close a risk-based clean-up:

Risk-Based Clean-Up and Free Product, Groundwater and Soil Vapor Gas

Petroleum Contaminated Soil (PCS) and/ or Free Product:

Up to seven (7) soil samples are taken to establish a representative sample and delineate the vertical and lateral extent of the pocket of petroleum-impacted soil, and potential or actual groundwater impacts. If it is determined that there is free product or large volumes of heavily contaminated soil, from which product may continue to migrate, mitigating the risk by excavation and off-site removal would be required, to the maximum extent practicable.

Risk-Based Clean-Up

Petroleum Contaminated Soil (PCS) seen during an excavation. The PCS is pictured here in the greyish color.

Risk-Based Clean-Up

The side view of the PCS, here you can see the coloration difference between the contaminated and the native soil.

Risk-Based Clean-Up

Free Product refilling into a sample boring hole

Risk-Based Clean-Up

Free Product within a sampling tube

Groundwater:

Has groundwater at the site at risk or has it been impacted by the diesel contamination?

In order to determine if groundwater has been or could be potentially encountered, a 10’ separation is required by the DEQ between the vertical extent of the contaminated soil and any potential shallow groundwater.

If there is no impact or potential impact to groundwater?

The groundwater investigation is now completed, no further action would be required.

If groundwater has been or has the potential to be impacted, what are the next steps?

A representative well will be installed in the source area to determine if groundwater has been impacted by the release. The installation of the representative well is designed to obtain a groundwater sample to measure, if any, the water level elevation in the contaminated water or soil.

If the samples in the representative well have detections that exceed the DEQs Ingestion and Inhalation from Tap Water Risk-Based Clean-Up levels, a groundwater investigation is necessary. The groundwater investigation determines the extent of the contaminated groundwater, and whether it is limited only to the property of the leaking UST or if extends to neighboring properties.

If the samples in the representative well meet the DEQ Ingestion and Inhalation from Tap Water Risk Based Clean-Up levels, no further action would be required.

The 10’ separation boring cannot be obtained due to site conditions, what happens to the investigation?

If a 10’ separation boring cannot be completed due to examples like refusal (rocky soil, etc.) or if the tank is too deep, per the DEQ a Beneficial Well Survey would need to be conducted.

A Beneficial Well Survey determines if a release of hazardous substances has impacted or has the potential to impact groundwater or surface water, through contaminant migration. These determinations will be used for evaluating exposure pathways in human health and ecological risk assessment; for identifying hot spots of contamination; and for selection or approval of remedial actions at hazardous substance clean-up sites.

The DEQ requires the survey to identify all properties that are in proximity to the site with the leaking underground storage tank, which may be utilizing a water supply well. The well may be used for drinking water, irrigation, etc. DEQ regulations considers that any well on a property that is for domestic use, be accounted for. These surveys can and are conducted within and outside city limits.

Grd Water

Groundwater encountered within an opening within an underground storage tank.

Vapor Intrusion from soil or groundwater:

Vapor intrusion is the migration of Volatile Organic Compounds (VOCs) from the subsurface into buildings. Per the DEQ, vapors released from volatile substances can be slowly released from underground spills. These volatile constituents move upward through the pores in the soil, when the soil is exposed during excavation, as well as, from contaminated groundwater. The DEQ requires Soil Vapor Gas sampling (SVGs) to assess the potential of carcinogenic vapors entering residential buildings. When certain constituents of interest, such as benzene, ethylbenzene and naphthalene concentrations exceed the DEQ Vapor Intrusion into Residential Buildings Standards, soil vapor gas sampling would be required.

To assess the potential cancer risks from vapor intrusion into homes, soil vapor gas sampling is triggered if any of the following variables apply:

  • The plume of contamination exceeds 65 cubic yards
  • There are, or likely to be, buildings within 30 feet of Volatile Organic Compounds (VOCs)
  • A 10’ separation cannot be established between the vertical extent and any potential shallow groundwater

Due to site specific factors, the number and sample locations may vary. Sampling may be conducted within the home or on the exterior of the building, either through the sub-slab and/or the soil.

Risk-Based Clean-Up

Soil Vapor Gas Sampling at the exterior of the property

Risk-Based Clean-Up

Sub-Slab Sampling, in the interior of the building

For a more in-depth overview of the DEQs requirements and standards regarding Risk-Based Clean-Up and leaking tanks, please visit their Leaking Underground Storage Tank Program (LUST site) DEQ LUST Site.

Generic Remedy Clean-Up

Generic Remedy Clean-Up

A Generic Remedy Clean-Up is considered a mid-level contamination, consisting of a release of 501 – 10,000 PPM. This remediation is a soil-only clean-up as long as there is no impact to groundwater, no free product is present and there is no vapor intrusion into the home or building. A generic remedy may require soil removal, as well as additional soil samples around the tank to determine the extent of the contamination. Total Petroleum Hydrocarbon (TPH) concentrations up to, but not exceeding, 10,000 PPM of soil may be left in place if:

  • There is at least three feet of clean soil over the contaminated soil
  • The volume of remaining contaminated soil (over 500 PPM) does not exceed 65 cubic yards
  • Analysis for the presence of benzene, ethylbenzene and naphthalene must be performed on all samples exceeding 2,500 PPM.
Generic Remedy Clean-Up

Generic Remedy Clean-Up – this is the fill cap from a tank that was decommissioned through a generic remedy remediation. The concrete was cut in order to gain access to the tank underneath the concrete patio.

Generic Remedy Clean-Up

Generic Remedy Clean-Up – Fill material from a tank that was being decommission through generic remedy remediation, this tank was found to have leaked at 5710 PPM

Once the investigation of the soils around the tank and the contaminated soil has been removed, the generic remedy clean-up decommissioning of the tank can continue.

In order to establish if a generic remedy is necessary, the DEQ requires a site assessment must be conducted to determine the source, nature, magnitude and extent of the contamination associated with a release from the underground storage tank. The site assessment must specifically address:

Generic Remedy Clean-Up Investigation

  • Determine the presence of free product
    • If there is pooling of liquid fuel in the tank excavation area or if there is clearly visible saturated soil, free product is present and a generic remedy remediation is no longer acceptable.
  • Determine if groundwater is affected and the depth to groundwater
    • During the tank excavation, if groundwater impact is discovered, the DEQ requires the water be pumped from the pit. If the pit remains dry for 24 hours, sampling and clean-up may proceed under the generic remedy. If water returns in less than 24 hours, it is presumed to be groundwater and the use of the generic remedy remediation is not allowed.
  • Determine the vertical and horizontal extent of the heating oil contamination
    • If decommissioning will be performed by removing the tank, two samples must be taken from each end of the excavation, at least 6 inches below the bottom of the excavation. If, by visual observations, additional contamination or odors are detected, samples must be collected from these areas as well.
    • If the decommissioned tank is to stay within the ground, two soil samples are to be taken from each end of the tank, as well as one below the tank bottom. The samples are to be taken no more than six inches from the tank end and at least one foot below the tank bottom. If contamination or odors are encountered, based on visual observations, samples must also be collected from these areas as well.
    • An estimated volume of contaminated soil proposed to remain at the site will be required to ensure that the 65 cubic yard limitation is not exceeded. Results of soil samples analyzed for the presence of heating oil are required to determine both the vertical and horizontal extent of contamination remaining above 500 PPM.

We have provided a link, this provides more insight to understanding more of the DEQs requirements regarding Generic Remedy Clean-Up remediation standards and guidelines.

UST Soil Sampling and Tank Inspection

Soil Sampling and Tank Inspection Common Questions

A UST Soil Sampling and Tank Inspection is almost identical to a Soil Sample.  The major difference between the two is that besides sampling between 12″ to 24″ beneath the bottom of the tank, the tank itself is opened up and inspected for its contents.

Why would a Tank Inspection be needed?

There are a couple different reasons that it is required to include the additional service of the Tank Inspection to the Soil Sampling, here are a few examples of why that would be needed:

  • During a tank search an underground storage tank was found, yet the technician was unable to get the fill cap off to determine its contents.  The fill cap may be inaccessible due to the cap being covered over, rusted shut or the fill pipe itself is completely filled and the contents of the tank can not be determined.
UST Soil Sampling and Tank Inspection

UST Soil Sampling and Tank Inspection – Tank found under concrete patio, fill cap inaccessible due to patio pavers.

  • The tank had been decommissioned previously but never registered with the DEQ.  In order for the underground storage tank to be registered with the DEQ, the soil beneath the tank needs to be sampled and the contents of the tank need to be verified.

The Tank Inspection

How do you perform a Tank Inspection?

After the tank has been located and marked out for soil sampling, our technicians will dig down to the top of the tank, cut open the tank and verify the contents.

Once the tank has been opened up, what is the best case scenario?

What we always hope for is clean soil samples and a properly decommissioned tank.  With samples below the DEQ reporting level of 50 PPM and a tank filled with clean material, the UST can then be registered with the DEQ.

UST Soil Sampling and Tank Inspection

UST Soil Sampling and Tank Inspection – Properly decommissioned tank filled with a concrete slurry.

What if the tank has been decommissioned with a proper fill material, but not filled all the way to the top of the tank, and the soil samples come back below the DEQ reporting level?

As long as the samples come in below the DEQ reporting level of 50 PPM, the remaining gap can be filled with additional fill material to ensure the tank has been decommissioned properly.  Once the tank has been certified as decommissioned, it can now be registered with the DEQ.

UST Soil Sampling and Tank Inspection

UST Soil Sampling and Tank Inspection – Tank inspection with gap in the proper fill material, tank will be filled with additional fill material and can then be registered with the DEQ

 

What are additional circumstances that are encountered with Tank Inspections?

Fill Material

  • Gap in proper fill material, below reporting level of 50 PPM:  Fill void with additional fill material and the tank can then be registered with the DEQ.
  • Proper fill material, leaking tank above 50 PPM: Tank has been decommissioned properly, remediation is required to determine that the leak has been contained. Once the clean-up is completed, the tank can then be registered with the DEQ.
  • Improper fill material: Improper fill material needs to be removed and the tank re-decommissioned. Additionally, if the tank is leaking above 50 PPM, remediation will need to take place to clean-up the site. Once the new decommissioning is completed, the tank can then be registered with the DEQ.

Water

  • Water in gap of the proper fill material, below reporting level of 50 PPM: Pump water out of the void and fill gap with additional fill material. Tank can now be registered with the DEQ.
  • Water completely fills the tank: Regardless of the fill material, everything within the tank needs to be pumped out and replaced with new fill material. Additionally, if the tank is leaking above 50 PPM, remediation will need to take place to clean-up the site. Once the new decommissioning is completed, the tank can then be registered with the DEQ.
UST Soil Sampling and Tank Inspection

UST Soil Sampling and Tank Inspection – Liquid found inside of opened tank

  • Tank is opened and it is empty.  If the samples come in below 50 PPM, the tank can be decommissioned and registered with the DEQ.  If the samples come in above 50 PPM, the tank can be decommissioned with remediation and then registered with DEQ
UST Soil Sampling and Tank Inspection

UST Soil Sampling and Tank Inspection – Empty tank discovered during a Tank Inspection.

UST Soil Sampling

UST Soil Sampling Common Questions

Whether a tank search has resulted in a UST being discovered or if there is an in-service tank on the property, EcoTech highly recommends soil sampling be completed around the tank.

If you are a buyer, it is imperative for you to obtain soil samples on the underground storage tank, as once you purchase the property, you have now purchased the UST and if it is leaking, are now responsible for the clean-up.

If you are a seller or a homeowner thinking about selling, and you know you have an UST on your property, preemptive soil samples will allow you prepare for pre-inspection complications.

For more information on underground storage tanks and real estate transactions, please see the DEQ Buying or Selling guide for helpful tips DEQs Buying or Selling a Home with a UST

What if a UST is found?

Soil Samples are recommended. Per Oregon DEQ, the best way to determine if a UST has leaked, is to have soil samples collected from under each end of the tank and have the samples analyzed for diesel and heavy oil. Each sample should be analyzed at an independent laboratory that is DEQ certified.

UST Soil Sampling

UST Soil Sampling – Rendition of technician taking soil samples 12-24″ beneath an underground storage tank.

UST Soil Sampling

UST Soil Sampling – Sampling tubes filled with soil from around an underground storage tank. The soil is then placed in a jar and sent to the lab for testing.

There is an in-service tank, should I perform soil samples?

As a prospective buyer, it is essential to test a tank before purchasing the property to determine if it has leaked or is currently leaking. The current property owner is responsible for any necessary contamination clean-up from a leaking underground storage tank. Purchasing a property without testing a tank makes you, as the new property owner, liable for a prior or currently leaking UST.

I’m selling my home and the buyer has found a tank, what are the next steps for me?

EcoTech recommends that you decommission the tank and register it with DEQ. Although, through our experience, buyers and their agents will require at a minimum proof of clean soil samples.

Types of Soil Samples

What are the type of UST soil samples? 

There are three different categories that sample results can be placed into:

Non-Detect (ND)

In-service tank: samples that were analyzed have come back as non-detect and no further tests are necessary. EcoTech does recommend that the decades old tank be decommissioned and a new heat source chosen, as soon as it is practical, before the tank does leak.

Out-of-service tanks: samples that were analyzed have come back as non-detect and no further tests are necessary. EcoTech does recommend that the out-of-service tank be decommissioned within 90 days of the soil samples and registered with DEQ.

*For both the in-service and out-of-service non-detect samples that were taken from each end of the UST, does not rule out the possibility of contamination underneath the soils of the tank, that is why EcoTech recommends decommissioning of the UST.*

50 PPM (parts per million) or less

In-service tank: samples that were analyzed indicate that a leak is present. Although this is a low detection and it is not reportable to DEQ, it indicates a leak has started and should be a concern. EcoTech highly recommends that the tank be taken out-of-service and decommissioned and registered with the DEQ.

Out-of-service tank: samples that were analyzed indicate that a leak is present. Although this is a low detection and it is not reportable to DEQ, it indicates a leak has started and should be a concern. EcoTech recommends that the out-of-service tank be decommissioned and registered with DEQ.

50.1 PPM or Greater

In-service or out-of-service tanks: “The OR DEQ requires that any site where a soil sample analysis shows petroleum concentrations of 50 PPM or greater, must be reported to the DEQ within 72 hours. Remediation will be determined based on the extent of the contamination.” Simply put, the tank is leaking above the reporting limit, EcoTech is required to report the leak to the DEQ, corrective action is now needed to clean-up the site.

Underground Storage Tank or UST Decommissioning

Underground Storage Tank or UST Decommissioning Common Questions

 

What does it mean to decommission a UST?

The most generic term, is to take the tank out of service.  Underground Storage Tank or UST decommissioning is accomplished by ensuring the tank has been properly cleaned and removed or completely filled with an inert material. The inert material consists either of perlite, a sand-like material or slurry, concrete.

If the tank is to be registered with DEQ, two soil samples will be taken from inside the bottom of the tank, after being pumped and cleaned, and analyzed for diesel and heavy oil. Each sample needs to be analyzed at an independent laboratory that is DEQ certified.

If the samples come back as non-detected, the tank can be then registered with the DEQ.

If the samples come back above the DEQ reporting limit (50.1 PPM), remediation will need to take place and once the corrective action has been completed, the tank will be registered with DEQ.  If soil remediation is need, please see our Decommissioning via Heating Oil Contaminated Soil Clean-Up page.

Why should homeowners decommission their UST and register it with the DEQ

I’ve emptied my tank of oil years ago and don’t use it any more, doesn’t that mean it is decommissioned?

No, in order to decommission the tank you will need to take the tank permanently out of service. This is completed by either removing the tank or filling it in place with an inert material.

Can I decommission my own UST?

According to the DEQ, it is legal for a homeowner to decommission their own UST, assuming that you perform the work yourself and comply with all applicable local, state and federal rules. Before deciding to decommission your own tank, the DEQ highly recommends that you read the DEQ Cleanup Guidance for Homeowners to understand the full scope of work involved in completing a decommissioning project. DEQ Decommissioning Guide for Homeowners

I’m selling my home and have switched over to gas years ago, should I decommission my tank?

It is not a requirement to decommission your tank before selling your home. Unfortunately in this highly active real estate market, many buyers will require at a minimum, proof of recent clean soil samples. Additionally, you will need to provide the buyer with documentation that the tank has been pumped of all of its contents. DEQ Out of Service Tank Requirements

Do I have to decommission my UST?

No, it is not a requirement to decommission your tank once you stop using it.  However, if you are thinking about selling your home, most buyers and their agents request decommissioning and registration before closing. Per DEQ, you will need to ensure that the tank has been emptied of oil and you will need to provide that documentation to the new buyer.  DEQ Requirements for Tanks No Longer in Use

Do I have to register my UST?

It is not required by DEQ to register the tank, but it is highly recommended. However, if you are decommissioning the tank as part of the sale of the home, this is usually a prerequisite prior to closing.

Why should I register my UST?

There are three primary benefits of registering the UST decommissioning with the DEQ:

  1. The decommissioning becomes public record.  So, even if your copy of the paperwork is misplaced or the name of the contractor that performed the work is forgotten, the record remains in the DEQ files.
  2. When the DEQ changes any of their rules (i.e. reporting limits, remediation guidelines, etc.), previously closed or registered tanks are “grandfathered” in.  Tanks that were decommissioned and not registered are subject to the new rules.  For example, over time the DEQ required the locations of soil sampling to change.  Meaning a previously unregistered decommissioned tank, would need to obtain additional soil samples to bring the tank up to the new DEQ sampling requirements.
  3. Most buyers are requiring DEQ registration because they don’t want to deal with future DEQ rule changes.  Even if you don’t plan to sell the property any time soon, registering the tank now can prevent added costs prior to and during a future sale.

I have a tank that was decommissioned years ago, but never registered with the DEQ, how do I now get it registered?

In order to establish if the tank has been decommissioned properly, soil samples and a tank inspection would be required. Soil samples need to be taken in order to determine if the tank had leaked prior to decommissioning. A tank inspection is necessary to establish if the tank has been decommissioned properly.

If the soil samples are clean and the tank has been decommissioned properly, the tank then can be registered with the DEQ.

USTs that have been Decommissioned inproperly

What happens if it isn’t decommissioned properly?

There could be a couple of different reasons a tank has not been decommissioned properly.  There may be inadequate or contaminated fill material, water within the tank or simply something that shouldn’t be in the tank (i.e. paint cans, large rocks, etc.).  Besides what is inside the tank, the soil samples will need to be taken into consideration to allow the tank to be certified as decommissioned to register with the DEQ.

  • Fill Material:  If the fill material within the tank is not an approved by the DEQ, that material will need to be removed and the tank will be re-decommissioned to DEQ standards for certification.  The same reasoning will go with contaminated fill material, even if it is DEQ approved material.  The contaminated material will need to be removed and the tank will need to be re-decommissioned to DEQ standards for certification.
  • Water:  If there is water within the tank, all water will be pumped out of the tank and re-decommissioned in order to certify with the DEQ.
  • Unconventional Items:  From time to time, items are found within a tank that should NOT be there.  Items such as large boulders, paint cans, trash cans and even tires have been discovered within a tank.  If this situation does arise, all items will need to be removed and disposed of in a landfill and the tank will need to be decommissioned.
Underground Storage Tank or UST Decommissioning

Underground Storage Tank or UST Decommissioning – Concrete, pain cans and water found within a tank.

What exactly do you do to decommission a tank?

In order to decommission an underground storage tank, we need to follow some step-by-step processes to ensure that we are able to take soil samples and inspect the tank properly.  This is the process by which EcoTech begins each in-place underground storage tank decommissioning project:

1.  We dig down, expose the tank and cut it open.

Underground Storage Tank or UST Decommissioning

Underground Storage Tank or UST Decommissioning – Exposed tank top.

2.  All tank contents are removed; heating oil, residual liquids, sludge.

3.  Clean and dry the tank interior and inspect it for holes.

Underground Storage Tank or UST Decommissioning

Underground Storage Tank or UST Decommissioning – Holes from within a tank.

4.  Collect soil samples from the inside and through the bottom of the tank.

Underground Storage Tank or UST Decommissioning

Underground Storage Tank or UST Decommissioning – The technicians cut two holes in the bottom of the tank to expose the soil underneath, two samples are then “grabbed” underneath the tank bottom.

5.  Soil Samples are submitted to the lab the same day for analysis, with results typically back the next business day by noon.

6.  Pending favorable laboratory results (less than 50 PPM), the tank can be backfilled with perlite or slurry.

***If soil sample results come in above the 50 PPM, remediation would be required to bring the site up to DEQ requirements.  (Please see our Heating Oil Contaminated Soil Clean-Up section for additional information on remediation Clean-Up with Decommissioning).

Underground Storage Tank or UST Decommissioning

Underground Storage Tank or UST Decommissioning – Tank filled with slurry.

7.  After the tank has been filled, the tank is then covered back over with the previous landscape (i.e. grass, concrete, dirt, etc.).